Other Products
Moldables |
 |
Nutec Procal Moldable is multipurpose form of fiber dispersed in a sticky, cohesive binder system that adheres to most ceramic, refractory or metallic surfaces. Nutec Procal moldable is used to prevent heat loss caused by the deterioration of the existing lining and can be installed using a trowel, a caulking gun or a pump. Ideal for repairing Nutec Procal shapes, seals, etc. After drying ( can be air drying, but we recommend air at temperatures near 100°C), the final form will be homogenous, highly insulator, strong and light weight. |
| |
| Characteristics |
A1 |
A1E(1) |
| FIBER TYPE |
Ceramic |
Biosoluble |
| MAX WORKING TEMPERATURE (ºC) |
1100 |
1100 |
| DENSITY APROX. (Kg/Lt) |
| WET |
1,4 |
1,4 |
| DRYED |
0,7 |
0,7 |
LINEAR SHRINKAGE
(24 hours at 1100 ºC) |
2% |
1,6% |
| COLOR |
White |
Note: Shelf life will be 6 months with the original seal.
(1) Ceramic fiber free product. Exonerated from carcinogen classification according to Directive 97/69/CE note Q |
|
 |
Rigidizer |
|
Nutec Procal Rigidizer is applied to the surface of Nutec Procal Shapes by spraying or brushing. After air-drying Nutec Procal Rigidizer firms-up the vacuum formed shape giving it tougher, more abrasion resistant characteristics |
| |
| Characteristics |
| MAX. WORKING TEMPERATURE (ºC) |
1250 |
| |
| DENSITY APROX. (Kg/m3) |
1,12 |
| CHEMICAL ANALYSIS (%) |
SiO2 |
>99 |
| |
Na2O |
0,3 |
| PH |
9 |
| COLOR |
White |
Can be applied by sprayed or brushed for different hardness
Data is the mean measurements of normal conditions obtained in laboratory tests |
|
|
Adhesive |
|
Nutec Procal Adhesive Application: Sealant Binding compound ( Paste ) |
| |
| Characteristics |
| APPIRIANCE |
Mix paste, Shipped in 20 lts drums ( 5 Gallon) |
| DENSITY |
1.55 - 1,70 g/cc |
| CHEMICAL Analysis (%) |
SiO2 |
38 - 42 % |
| |
Al2O3 |
9 - 13 % |
| |
Na2O |
4,8 -5,6 % |
| |
K2O |
1,3 - 2,1 % |
| |
H2O |
38 - 44 % |
Product must be covered during storage, avoiding dramatic temperature changes ( keep +40°C, -5°C)
Avoid skin contact, use rubber gloves. If skin contact occurs, wash the affected part with warm water |
|
|
Paint |
|
Nutec Procal Paint is a Finishing Paint based on pure silicone anticaloric resins. Fast drying. Can be applied to the Nutec Procal vacuum formed shapes reducing the porosity and can be liquid proof on applications below 400°C. |
| |
| Characteristics |
| MAX. WORKING TEMP (ºC) |
600 |
| |
| DENSITY (Kg/Lt) |
1,1 |
| VISCOSITY |
80'' Ford cup nº4 INTA 162017ª |
| SOLIDS |
40% ASTM D-2697 |
| COLOR |
Black |
| DRYING |
20 Minutes at 200 ºC |
| Recommended THICKNESS |
10 a 15 microns (Higher thickness can produce bubbles with the temperature) |
| Aprox. YIELD |
3 a 4 m2 / lt |
This product can be applied direct to the surface, air-dray. The coat can be liquid proof if application does not exceed 400°C |
|
|
|
